高清不卡一區二區_先锋稳定亚洲每日资源网_国产精品二区在线观看_欧美性受群交在线观看_女人弄爽到高潮免费视频网站_精品国产群3p交换99_免费美女视频网站_蜜桃视频一区_婷婷综合缴情亚洲狠狠小说_稚嫩娇小哭叫粗大撑破

歡迎進入東莞市安泰科精密五金有限公司網站
全國服務熱線
0769-83885215
熱點資訊
切削參數，齒距的換算
徑節滾花-換算表
時間: 2018-12-18 15:33 瀏覽次數：
Blank diameters for diametral pitch knurling dies are more easily computed, since they are always common fractional sizes. The formula is as follows: Blank Diameter = ( #Teeth [part] / Diametral Pitch ) American Standard ANSI B94.6-1984 des

相司徑節的工件因?yàn)榕c滾花輪的齒節距相同，所以更容易計算，如下表：

Blank Diameter = ( #Teeth [part] / Diametral Pitch )
American Standard ANSI B94.6-1984 describes the diametral pitch knurl system. Diametral pitch knurls are designed to track uniformly on fractional size stock up to 1" in multiples of 1/32" or 1/64". They are held to closer tolerances for this purpose.

The American Standard recommends that the use of 64 Diametral Pitch knurls be avoided as much as possible, and that preference be given to the use of 96 D.P. knurls for simplification of tooling. (For Equivalent Normal Circular TPI see below.)

The number of teeth that will be rolled can be easily determined by multiplying the blank diameter by the Diametral Pitch of the knurl. Example: A 96 D.P. knurl will roll 96 x 1/2 = 48 teeth on a 1/2" diameter stock.

D.P.Blank Diameters for Uniform Tracking64every 1/64"96every 1/32" (also every 1/96")128every 1/64" (also every 1/128")160every 1/32" (also every 1/160")
D.P.Equivalent Normal Circular TPIStraight Teeth30° Diagonal6420.723.99630.835.612841.147.416051.259.1 

NOTE: Unfortunately the above formulas do not hold precisely for all conditions. Sometimes apparently identical knurls from different manufacturers will not track on the same blank diameters due to a difference in the sharpness of the teeth. Also, it is possible for the number of teeth rolled on a part to change as the knurling tool wears. How deeply the knurl penetrates into the work blank on the first revolution is the main factor in determining if an adjustment should be made to the basic formula.

Some factors which affect this penetration are:

  1. In-feed rate (or axial feed rate for knurling from the turret)

  2. Sharpness of the knurl teeth

  3. Hardness of the material

  4. Included tooth angle of the knurl (a sharper angle pentrates easier)

  5. Width of knurl face (a narrow face penetrates easier)

  6. Method of knurling (bump from cross-slide or end knurling from turret)

  7. Bevels on edges of part or knurl tool (affects knurl penetration from end)

A change in any of the above variable may correct (or cause) a mis-tracking problem.         


Copyright ? 2018 東莞市安泰科精密五金有限公司 版權所有      備案號： 粵ICP備19073278號-1
全國服務電話：0769-83885215     傳真：0769-83971520
地址：廣東省東莞市常平鎮蘇坑樂園路14號

電話
服務電話：
0769-83885215
微信

微信公眾號